----------------------- | :------------------: | :------------------------------------------------------------ | | Section classification | Table 5.2 | None — recommended values adopted | | Bending resistance Mc,Rd | Clause 6.2.5 | γM0 = 1.0 (adopted) | | Shear resistance Vc,Rd | Clause 6.2.6 | γM0 = 1.0 (adopted) | | Bending + shear interaction | Clause 6.2.8 | No modification | | LTB — General case | Clause 6.3.2.2 | UK NA Table NA.4 specifies buckling curves | | LTB — Simplified method | Clause 6.3.2.3 | UK NA allows for buildings ≤ 4 storeys | | Deflection limits | EN 1990 Annex A1.4.3 | UK practice: span/200 total, span/250 imposed (NA to EN 1990) | | Partial factors | Clause 6.1 | γM1 = 1.0, γM2 = 1.25 (UK NA) |

Serviceability and Deflection — UK Practice

UK engineers typically apply the following deflection limits:

• Floor beams (general): δmax ≤ span/200 for total deflection, ≤ span/250 for imposed load increment
• Floors supporting partitions: δmax ≤ span/360 for imposed load (to avoid partition cracking)
• Roofs: δmax ≤ span/200 total, span/250 imposed (snow)
• Pitched roof purlins: δmax ≤ span/200, but check ponding stability for low-slope roofs

For the 533×210 UB 92 example under service load (w = 28.6 kN/m unfactored): Δ = 5 × 28.6 × 7500⁴ / (384 × 210000 × 554 × 10⁶) = 16.9 mm < 7500/200 = 37.5 mm → OK.

The UK National Annex to EN 1990 (NA to BS EN 1990:2002+A1:2005) provides additional serviceability criteria for vibration, including natural frequency checks for floors subject to rhythmic activities.

Related Resources

• UK Steel Design Guide
• UK Beam Design Guide
• UK Steel Grades
• UK UB/UC Section Properties
• UK Steel Beam Sizes

FAQ

What is the difference between UK and EU beam design? The UK uses EN 1993-1-1 with a UK National Annex that specifies modifications to partial factors, buckling curve selection, and LTB assessment methods. The core calculation methodology is the same as Eurocode 3.

Does the calculator use UK or European buckling curves? The calculator uses the UK National Annex recommended buckling curves for UK sections. UB sections typically use curve 'a' for minor axis buckling, while UC sections use curve 'b' or 'c' depending on flange thickness.

What steel grade is most common in UK construction? S355 is the most widely used structural steel grade in the UK, followed by S275 for lighter applications. S460 is available but less common in building structures.

Are UK and European sections the same? UK UB and UC sections are based on BS 4-1, which differs from European IPE/HEA/HEB sections. UB sections have a different flange width-to-depth ratio compared to European sections.

What are the UK-specific LTB buckling curves? Per UK NA Table NA.4, UB sections with h/b > 2 use curve 'b' (αLT = 0.34) for lateral-torsional buckling. UB sections with h/b ≤ 2 use curve 'c' (αLT = 0.49). UC sections generally use curve 'c'. The UK NA adopts different curve selections than the EN 1993-1-1 recommended values for certain section types.

How does the simplified LTB assessment work for UK buildings? The UK NA to EN 1993-1-1 Clause 6.3.2.3 allows a simplified LTB assessment for beams in buildings up to 4 storeys. When the compression flange is restrained by a floor slab at centres ≤ Lm (limiting length from Table NA.5), LTB may be deemed satisfied without detailed calculation. Lm varies by section size and steel grade.

What is the UK NA position on γM2 for connections? The UK NA to EN 1993-1-8 adopts γM2 = 1.25 for bolted and welded connections (NA.2.4), which matches the EN 1993-1-8 recommended value. Note that the UK NA to EN 1993-1-1 uses γM2 = 1.1 for net section fracture at the ultimate limit state (Clause 6.2.3) — this is a separate application from connection design and should not be confused with the connection partial factor.

Do UK deflection limits differ from Eurocode defaults? Yes. The UK NA to EN 1990 specifies span/200 for total deflection and span/250 for imposed load deflection as the recommended limits, which are more relaxed than some European interpretations. However, many UK designers use the more stringent SCI P385 guidance for sensitive floors.

Disclaimer: This content is for educational purposes only. Results must be verified by a licensed professional engineer. Steel Calculator provides preliminary design tools — NOT a substitute for professional engineering judgment.